This indicates that your Litter-Robot can’t locate the Dump position.įlashing from right to left or in a blue-yellow-red pattern, on the other hand, means that the machine can’t locate the Home position this time. The lights may also flash from left to right or in a red-yellow-blue pattern. Then, disassemble and check for any blockages on the gears and motors. To resolve this, turn off and unplug your Litter-Robot first. The yellow and red lights may flash sequentially, and this signals a motor obstruction. They notify you that something is wrong, and you need to look into the problem or contact the manufacturer. These flashing patterns are usually indicators of an underlying issue. The colored lights can also flash sequentially or simultaneously. Related: Litter-Robot Keeps Getting Stuck Sequential and Simultaneous Flashing Once you’ve checked these off, press the Reset button to reboot your Cat Sensors. If the problem is the latter, make sure you refill your machine with the right amount of litter and that your Waste Drawer isn’t too stuffed. This is either because your cat won’t leave the Globe or there’s excess weight on your Litter-Robot. You can change this depending on your need by pressing and holding the Empty button until you enter the settings for Wait Time.Ī flashing red light occurs when the Cat Sensor has been activated for more than 2 minutes. The countdown or Wait Time upon your cat’s exit is set at 7 minutes by default. When your cat leaves the Globe, the machine will count down and then start a cleaning cycle. Red LightĪ solid red light, on the other hand, means that the Litter-Robot’s Cat Sensor activated while the machine was on standby. When this happens, you’ll have to email manufacturers for recalibration of the sensors. It’s also possible that sensors get a little faulty over time. Litter dust can sometimes mess with the sensors, so make sure you do this regularly too. If the blue light is still flashing even after installing fresh liners, you can try to locate the Drawer Full indicators in the Waste Drawer and wipe it clean. Recommended: Litter Robot vs Catlink full comparison The manufacturer recommends that you run a cycle or two after changing liners. This should leave you with a solid blue light once again. Simply empty the Waste Drawer and replace the soiled liner bag with a fresh one. A flashing blue light, however, signals that the Waste Drawer is full and requires changing. This means it’s ready for use and currently has no issues whatsoever. Generally, a solid blue light means that your Litter-Robot is currently on standby. Below we’ll see what they mean and what you should do when they also start flashing. Other Lights and What They MeanĪside from yellow, the Litter-Robot sports two more colored lights: blue and red. Then, turn the machine on again and press the Reset button. The solution for this is to turn off your Litter-Robot and check for any possible “pinch conditions,” such as objects or clumps stuck in the Waste Port. When the sensors are activated, the cycle pauses, and the yellow light flashes rapidly until resolved. These Anti-Pinch Sensors are part of the machine’s built-in safety features that ensure no cats are harmed during cycling. This means that your Litter-Robot’s Anti-Pinch Sensors are activated. The yellow light could also flash rapidly-around four flashes of light per second. Secure the bonnet and check if the cycle resumes afterward. If there’s no cat in sight, check the machine’s bonnet tabs on each side and make sure that none of them came loose. Once your cat leaves, the Litter-Robot should go back to running the usual cleaning cycle after a few minutes. The Cat Sensor protects your cat and will pause the cleaning cycle. To find out which of these is the issue, first, check if your cat is inside the Globe. This could be due to two things: a cat entered and the Litter-Robot’s Cat Sensor got activated mid-cycle, or the machine’s bonnet has been removed. Slow flashingĪ slow flashing yellow light-around one flash of light per second-ultimately means that something interrupted the cleaning cycle. Okay, but how do you know which one of the reasons listed above is your Litter-Robot’s current issue? First, you have to take a closer look at the way the machine’s yellow light is flashing. Litter Robot Yellow Light Flashing: A Closer Look Litter Robot Yellow Light Flashing: A Closer Look.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |